hit counter script
Sony DFP-R3000 Installation Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Card Reader
  5. DFP-R3000
  6. Installation manual
Sony DFP-R3000 Installation Manual

Sony DFP-R3000 Installation Manual

Sdds player system digital film sound reader.
Hide thumbs Also See for DFP-R3000:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual
SDDS Player System
DIGITAL FILM SOUND READER
DFP-R3000
®
INSTALLATION MANUAL
1st Edition (Revised 1)
Serial No. 10001 and Higher

Advertisement

Table of Contents
loading

Related Manuals for Sony DFP-R3000

Summary of Contents for Sony DFP-R3000

  • Page 1 SDDS Player System DIGITAL FILM SOUND READER DFP-R3000 ® INSTALLATION MANUAL 1st Edition (Revised 1) Serial No. 10001 and Higher...
  • Page 2 ! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.

  • Page 3: Table Of Contents

    Dimensions .................... 1-1 (E) Input/Output Signals of Connector ............1-2 (E) Installation ..................... 1-3 (E) 5-1. Use of DFP-R3000 for 70 mm Film .......... 1-3 (E) 5-2. Installation to the Projector ............1-7 (E) 5-2-1. Installing to SIMPLEX 35 (Strong International) ....1-8 (E) 5-2-2.

  • Page 4: Manual Structure

    This manual is intended for use by trained system and service engineers, describes the information when installing DFP-R3000. Related manuals ..DFP-R3000/DFP-D3000 Operation Manual (Supplied with the DFP- D3000) This manual is necessary for application and operation of the DFP-R3000.

  • Page 5: Installation

    Areas where the unit will be exposed to direct sunlight or D3000. any other storong lights. If the power of the DFP-R3000 needs to be turned OFF Dusty areas or areas where it is subject to vibration. when fault occurs, turn OFF the power of the DFP-D3000.

  • Page 6: Input/Output Signals Of Connector

    Signal level ; SDI format digital audio signal 4 G1 Pin No. Signal Description +24 V DC 24 V — No connection — Ground (DC 24 V) — CABLE SHIELD Ground (Frame) DATA SDDS data — DATA GND Ground (Data) 1-2 (E) DFP-R3000...

  • Page 7: Installation

    Use of DFP-R3000 for 70 mm Film The following describes how to install the DFP-R3000 to To use the DFP-R3000 for 70 mm film, the front panel, the various projectors indicated below. and roller guide need to be replaced, etc.
  • Page 8 B3 x 4 a B3 x 4 c Escutcheon Left side panel B3 x 4 c Roller guide shaft T1 (35) B2.6 x 6 d Front panel assembly Roller guide T1 assembly Washer RK4 x 8 Ornamental washer 1-4 (E) DFP-R3000...
  • Page 9 2. Attach the optional guide T assembly (70) using hexagon cap screw (4 x 10), spring washer (SW4) and washer (W4) from inside of the unit to the position from which the roller guide shaft T1 (35) was removed. Hexagon cap screw 4 x 10 Optional guide assembly (70) Optional guide T assembly (70) 1-5 (E) DFP-R3000...
  • Page 10 B3 x 4 a B2.6 x 4 h Supports B3 x 4 e B3 x 4 e B3 x 4 g Front panel (70) R Diagram of completion Supports Places for installing support DIGITAL FILM SOUND READER DFP-R3000 1-6 (E) DFP-R3000...

  • Page 11: Installation To The Projector

    5-2. Installation to the Projector Notes on Installation . Place the DFP-R3000 in the upright position (not sideways nor tilted) and position the reader (part of the drum where the LEDs are located) of the DFP-R3000 more than 32 frames but within 119 frames from the picture gate of the projector.

  • Page 12: Installing To Simplex 35 (Strong International)

    For attaching Path adjustment tool and DFP-R3000 Washer (W4, MID) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 Procedure Step 1. Installing the Adapter (A) to the Projector Path adjustment tool 1. Remove REEL ARM or platter guide roller of supply reel side of the projector.
  • Page 13 (W4) and four spring washers (SW4). (3/8-16) REEL ARM 2. Put the film on the projector from the DFP-R3000 and adjust the position (arrow direction A) of DFP-R3000 so that the film is smoothly fed onto the projector. DFP-R3000 3.
  • Page 14 Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-3000 Spring washer (SW4 TYPE2) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 Washer (W4, MID) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 Wave washer (10) —...
  • Page 15 8. After the adjustment has been completed, tighten the two hexagon cap screws (3/8) 2. 9. Remove the film from the path adjustment tool. 10. Remove the path adjustment tool from the adapter (EA). 1-11 (E) DFP-R3000...
  • Page 16 (M4 x 12) 4, four washers (W4) and four spring washers (SW4). REEL ARM 2. Put the film on the projector from the DFP-R3000 and adjust the position of DFP-R3000 so that the film is DFP-R3000 smoothly fed onto the projector.

  • Page 17: Installing To Simplex 70

    Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-3000 Spring washer (SW4 TYPE2) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 Washer (W4, MID) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 Procedure Step 1.
  • Page 18 (M4 x 12) 4, four (3/8-16) washers (W4) and four spring washers (SW4). 2. Put the film on the projector from the DFP-R3000 and REEL ARM adjust the position (arrow direction A) of DFP-R3000 so that the film is smoothly fed onto the projector.

  • Page 19: Installing To Century Jj (Strong International)

    Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-3000 Spring washer (SW4 TYPE2) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 Washer (W4, MID) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 Procedure Step 1.
  • Page 20 5 Hxagon cap (3/8-16) washers (W4) and four spring washers (SW4). REEL ARM 2. Put the film on the projector from the DFP-R3000 and DFP-R3000 adjust the position (arrow direction A) of DFP-R3000 so that the film is smoothly fed onto the projector.

  • Page 21: Installing To Norelco Aa-Ii 35/70 (Kinoton)

    Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-3000 Spring washer (SW4 TYPE2) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 Washer (W4, MID) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 1-17 (E)
  • Page 22 7. After the adjustment has been completed, tighten the Film two hexagon cap screws (5/16) 1. 8. Remove the film from the path adjustment tool. 9. Remove the path adjustment tool from the adapter (A). 1-18 (E) DFP-R3000...
  • Page 23 (M4 x 12) 4, four REEL ARM washers (W4) and four spring washers (SW4). 3. Put the film on the projector from the DFP-R3000 and adjust the position (arrow direction A) of DFP-R3000 so that the film is smoothly fed onto the projector.

  • Page 24: Installing To V5/V8/V9 (Cinemeccanica)

    Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-3000 Spring washer (SW4 TYPE2) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 Washer (W4, MID) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 Hexagon cap screw (M8 x 35)
  • Page 25 8. After the adjustment has been completed, tighten the Film four hexagon cap screws (M8 x 35) 2. 9. Remove the film from the path adjustment tool. 10. Remove the path adjustment tool from the adapter (EA). 1-21 (E) DFP-R3000...
  • Page 26 REEL ARM washers (W4) and four spring washers (SW4). 3 Hexagon cap screw 3. Put the film on the projector from the DFP-R3000 and (3/8-16) adjust the position of DFP-R3000 so that the film is smoothly fed onto the projector.

  • Page 27: Installing To P35 (Christie)

    Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-3000 Spring washer (SW4 TYPE2) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 Washer (W4, MID) — Supplied with DFP-R3000 For attaching Path adjustment tool and DFP-R3000 1-23 (E)
  • Page 28 8. After the adjustment has been completed, tighten the Projector two hexagon cap screws (3/8-16) 2. 9. Remove the film from the path adjustment tool. 10. Remove the path adjustment tool from the adapter (A). 1-24 (E) DFP-R3000...

  • Page 29: Checking And Adjustment After Installation

    (M4 x 12) 4, four DFP-R3000 washer (W4) and four spring washers (SW4). 3. Put the film on the projector from the DFP-R3000 and adjust the position (arrow direction A) of DFP-R3000 so that the film is smoothly fed onto the projector.
  • Page 30 Connection cable (50 m) ; 1 (Sony part No. 1-783-382-21) Connection 1. Connect the DFP-R3000 and DFP-D3000 with the following connectors using a connecting cable (10 m or 50 m) according to the installing environment. Turn OFF the power of the DFP-D3000 when connecting.

  • Page 31: Film Running Checking

    Procedure Perform the checks and adjustments with the DFP-R3000 connected to the DFP-D3000. (1) Load a film into the DFP-R3000 and projector, and then run the film and perform the following checking. Checking and Adjustment Items For details about loading film, refer to DFP-D3000/ R3000 Operation Manual.
  • Page 32 Tooth of sprocket Roller guide S1 Flange Perforations (holes) Sprocket Tooth of sprocket No gap Film Flange Gaps No gap Roller guide S2 Film entrance DEGITAL FILM SOUND READER Drum Roller Film retainer roller guide T1 Film exit 1-28 (E) DFP-R3000...
  • Page 33 R3000 and projector. DFP-D3000 System Setup screen. Be sure to mount the film through the picture gate. DFP-D3000 Test Menu Screen For details about loading film, refer to DFP-D3000/ (Screen for Version 2.00 Build 2.054) R3000 OPERATION MANUAL. 1-29 (E) DFP-R3000...
  • Page 34 HEADPHONES Rch : Center channel (C ch) output signal of SDDS digital play signal (3) Load the test film to the projector and the DFP-R3000, and run the film. For details on loading the film, refer to the DFP- D3000/R3000 OPERATION MANUAL.
  • Page 35 Lch and Rch signals are synchronized. editing of data set and viewing of operations of the unit. DFP-3000 System Set-up screen (Screen for Version 2.00 Build 2.054) 5) Click “Master SDDS Settings” at the Master Menu of the DFP-D3000 System Setup screen. 1-31 (E) DFP-R3000...

  • Page 36: Setting Up

    Master SDDS Settings screen, roughly adjust the delay amount (about 2 or 3 seconds) of After connecting the system, set the required following the physical position of the DFP-R3000 installed parameters for SDDS system setup. to the projector in frames.
  • Page 37 The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any...
  • Page 38 Printed in Japan Sony Corporation DFP-R3000 (SY) J, E 2000. 8 08 Communication System Solutions Network Company 9-968-522-02 ©1998...

Table of Contents