Sony WEGA KDL32XBR950, KDL42XBR950 Quick Start Manual
Sony quick start guide portable tv kdl32xbr950, kdl42xbr950
Hide thumbs
Also See for WEGA KDL32XBR950, KDL42XBR950:
- Quick start manual ,
- Service manual (172 pages) ,
- Operating instructions manual (136 pages)
Advertisement
Quick Links
KDL32XBR950
Checking the Supplied
KDL42XBR950
Accessories
Thank you for purchasing this
Remote Control
(RM-Y1000):
Sony product.
After following this step by step
guide you will be able to:
– Insert batteries into the
Antenna Cable:
remote control.
– Connect the display unit to
the media receiver unit.
• Speaker jack covers
– Connect a cable or antenna to
(KDL42XBR950 only)
your TV.
• Operating Instructions
– Tune your TV .
– Program your remote control
Inserting Batteries into
the Remote Control
Now you are ready for viewing
TV programs.
1
Open the battery compartment as illustrated below.
2
Insert two size AA batteries (supplied) by matching the e and E
terminals on the batteries to the diagram inside the battery
compartment.
3
Close the battery compartment.
US
© 2003 Sony Corporation
4-102-399-01(1)
Printed in Japan
1
Two size AA
Display Interface
batteries (R06 Type):
Cable:
Two AC power
cords:
• Quick Start Guide
• Warranty Card
2
Remove the batteries to avoid damage from possible battery leakage
whenever you anticipate that the remote control will not be used for
an extended period.
Handle the remote control with care.
Avoid dropping it, getting it wet, placing it in direct sunlight, near a
heater, or where the humidity is high.
3
Connecting the
Display Unit to the
Media Receiver Unit
1
Connect the display interface cable (supplied) to the DISPLAY
SIGNAL IN jacks, and the AC power cord (supplied) to the AC IN jack
of the unit.
KDL32XBR950
KDL42XBR950
SONY EXCLUSIVE CABLE ONLY
WHITE
BLACK
DISPLAY SIGNAL IN
Tighten the screw
Display Interface
AC power cord
slowly until the
cable (supplied)
(supplied)
screw is stabilized.
When you install KDL42XBR950, use the optional accessories as
follows:
• SONY TABLE TOP STAND: SU-P42T2
• SONY WALL-MOUNT BRACKET: SU-PW2
• SONY FLOATING STAND: SU-PF1
2
Connect the other end of display interface cable to the media receiver
unit's DISPLAY SIGNAL OUT jacks, and connect the media receiver
unit's AC power cord (supplied) to the AC IN jack .
CABLE
VHF/UHF
S400
(TS/DV/MICROMV)
i.LINK
WHITE
BLACK
~
AC IN
DISPLAY SIGNAL OUT
Display Interface cable
AC power cord
(supplied)
(supplied)
Tighten the screw slowly
until the screw is stabilized.
Be sure to use the supplied AC power cords.
When connecting optional components, do not connect the AC
power cords to wall outlets until you have completed making all
connections.
Do not tighten the screws too much. It may damage the screws.
Do not use damaged cables, such as cables whose connectors are
deformed.
Handle the display interface cable with care. This unit may fall and
cause injury if accidently knocked or pulled by the connected cable.
To store the AC power cord and the display interface cable in the
stand;
(KDL32XBR950)
See "Storing the AC power cord and the display interface cable
into the stand (KDL32XBR950 only)" on page 28 of the
operating instructions.
(KDL42XBR950)
See the operating instructions for the optional tabletop stand.
4
Connecting a Cable or
Antenna
The way in which you will connect your TV varies, depending on how
your home receives a signal (cable, cable box, antenna) and whether or
not you plan to connect a VCR or other optional AV equipment.
See examples A, B or C to connect your TV. For details on other
connection examples, see pages 31 to 54 of the operating instructions.
A Cable or Antenna
For best results, use this connection if you are connecting a
cable or an antenna and you;
• Do not need a cable box to unscramble channels.
• Do not intend to connect a VCR.
For antenna connection, use the supplied antenna cable.
Rear of Media Receiver Unit
CABLE
VHF/UHF
S400
(TS/DV/MICROMV)
i.LINK
WHITE
BLACK
~
AC IN
DISPLAY SIGNAL OUT
Antenna cable
or
75-ohm coaxial cable
(supplied)
(not supplied)
When using an indoor antenna, such as rabbit-ear or dipole-antenna,
keep the antenna away from the display unit. If not, noise may appear
on the screen.
B Cable Box and Cable
For best results, use this connection if;
• Your cable company scrambles some channels, such as premium
channels (which requires you to use a cable box), but does not
scramble all channels.
• You do not have a VCR.
75-ohm
IN OUT
CATV
coaxial cable
75-ohm
Cable Box
cable
(not supplied)
Splitter
coaxial cable
(not supplied)
Antenna cable
(supplied)
Rear of Media Receiver Unit
CABLE
VHF/UHF
S400
(TS/DV/MICROMV)
i.LINK
WHITE
BLACK
~
AC IN
DISPLAY SIGNAL OUT
Advertisement
Related Manuals for Sony WEGA KDL32XBR950, KDL42XBR950
Summary of Contents for Sony WEGA KDL32XBR950, KDL42XBR950
- Page 1 When you install KDL42XBR950, use the optional accessories as follows: • SONY TABLE TOP STAND: SU-P42T2 • SONY WALL-MOUNT BRACKET: SU-PW2 • SONY FLOATING STAND: SU-PF1 Connect the other end of display interface cable to the media receiver unit’s DISPLAY SIGNAL OUT jacks, and connect the media receiver...
-
Page 2: Tuning Your Tv
Beta/ED Beta VCRs: 303, 8mm VCR: 302, VHS VCR: 301, DVD outlets. player: 751, i.LINK: 901. If you have video equipment other than Sony brand that you want to control with the TV’s remote control, use the following procedure to program the remote control.