Cisco D9800 Getting Started
Network transport receiver
Hide thumbs
Also See for D9800:
- Reference manual (294 pages) ,
- Configuration manual (30 pages) ,
- Installing manual (12 pages)
Advertisement
Table of Contents
Getting Started
This section describes how to use the D9800 Network Transport Receiver front panel and web GUI, as well
as how to initially set up the D9800 receiver. There are two ways to configure the D9800 unit: front panel
and web GUI. For example, changes made through the front panel is reflected on the web GUI, and vice
versa.
•
•
•
•
About the Front Panel
You can use the controls and indicators on the front panel to operate the D9800 receiver. These include the
numeric keypad, the navigation or selection keypad, the LCD, the alarm and signal indicators. These are
shown in the following illustration.
Figure 1: D9800 Front Panel
LCD
The LCD provides information on the selections available at any menu level, current settings for parameters,
and certain status and alarm indications. This is a 2x40, backlit LCD display. The top line may be status data
About the Front Panel, page 1
Logging on to the D9800 Web GUI, page 7
Basic Vs. Advanced Mode, page 10
Quick Setup, page 10
Cisco D9800 Network Transport Receiver Version 3.11 Installation and Configuration Guide
1
Advertisement
Table of Contents
Related Manuals for Cisco D9800
Summary of Contents for Cisco D9800
-
Page 1: Getting Started
This section describes how to use the D9800 Network Transport Receiver front panel and web GUI, as well as how to initially set up the D9800 receiver. There are two ways to configure the D9800 unit: front panel and web GUI. For example, changes made through the front panel is reflected on the web GUI, and vice versa. -
Page 2: Front Panel Leds
• no IP input present. • no valid inputs are available. CI Slots The CI slots allow the use of CAM (Conditional Access Module) Smart Card to decrypt purchased programming. Cisco D9800 Network Transport Receiver Version 3.11 Installation and Configuration Guide... -
Page 3: Navigation/Selection Keypad
The MENU key can also be used to cancel a numeric entry at any point during the entry sequence, and the left arrow key allows backspacing through the entry. Cisco D9800 Network Transport Receiver Version 3.11 Installation and Configuration Guide... -
Page 4: Locking Or Unlocking The Front Panel
GUI. Step 1 From the D9800 web GUI, choose System Settings > Front Panel. Or, from the Main Menu of the D9800 front panel, choose Setup > Admin > KB Lock. - Page 5 Viewing the Channel Authorization Status From the Startup screen of the D9800 front panel, press the right or left arrow keys on the keypad to move to the PE entry authorization status screen. This screen displays all the available channels and whether the channels are authorized (Y or N).
- Page 6 The NIT Retune (NR) symbol indicates that a NIT retune recovery is in progress on the current receiver. The Session Open symbol indicates that you are changing a group of related items. Cisco D9800 Network Transport Receiver Version 3.11 Installation and Configuration Guide...
-
Page 7: Adjusting The Lcd Contrast
Step 2 Type the IP address of the D9800 Network Transport Receiver in the address bar and press Enter. You can view and configure the IP address in the following front panel menu: Setup > IP > IP > IP Address. - Page 8 D9800 Web GUI Environment D9800 Web GUI Environment The following is an example of the D9800 web GUI page: Figure 3: D9800 Web GUI The following table displays the general buttons on the D9800 web GUI. Button Description Apply Saves and applies the settings to the receiver.
- Page 9 Getting Started D9800 Web GUI Environment Alarms/Warnings The top right corner of the D9800 web GUI displays the total number of active alarms ( ), active warnings ), and clear messages ( ). Clear messages is calculated as follows: total number of alarms + total number of warnings - total number of active alarms - total number of active warnings.
-
Page 10: Quick Setup
Basic Vs. Advanced Mode All the D9800 features are available in the Advanced mode (default). However, you have the option of limiting the features available by switching to the Basic mode. The mode option is available at the top right-hand corner of the D9800 web GUI. - Page 11 MPEGOIP input/output option installed (D9800-SS-MPEGOIP). For multi-stream units (D9800-MS-MPEGOIP), configure the IP data output and stream settings. Typical Digital Program Mapping Setup Set the DPM mode. Cisco D9800 Network Transport Receiver Version 3.11 Installation and Configuration Guide...
- Page 12 Getting Started Quick Setup Cisco D9800 Network Transport Receiver Version 3.11 Installation and Configuration Guide...