Table of Contents
Advertisement
Checking the Configuration
You can use these three show controllers T3 commands for Cisco 7200 series, Cisco 7301 routers, and
Note
Cisco 7401ASR routers in which the PA-MC-2T3+ is supported. The syntax is as follows:
— show controllers T3 chassis-slot/T3-port brief
— show controllers T3 chassis-slot/T3-port tabular
— show controllers T3 chassis-slot/T3-port remote performance
Examples of these show controllers T3 commands for Cisco 7200 series and Cisco 7401ASR routers
are not shown.
The show controllers command with no arguments displays information about every controller and
interface in the router.
The following example is for a Cisco 7500 series router:
show controllers
•
Router# show controllers
Serial0/1/0 -
Framing is c-bit, Clock Source is Line
Bandwidth limit is 44210, DSU mode 0, Cable length is 10
Data in current interval (1 seconds elapsed):
0 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation
0 P-bit Err Secs, 0 P-bit Sev Err Secs
0 Sev Err Framing Secs, 0 Unavailable Secs
0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs
No alarms detected.
Fddi1/0 - hardware version 2.9, microcode version 20.4
Phy-A registers:
cr0 4, cr1 0, cr2 0, status 6, cr3 0
Phy-B registers:
cr0 4, cr1 4, cr2 0, status 3, cr3 0
FORMAC registers:
irdtlb
irdtrth F85F, irdtmax FBC5, irdtvxt 8585, irdstmc 0810
irdmode 6A21, irdimsk E000, irdstat 8060, irdtpri 0000
FIP registers
ccbptr:
memdptr:
frptr:
tx_claim_bc:
tx_pend:
tx_active_cnt: 0000
tx_state:
rx_pool:
rx_next1:
enabled:
phya_tmin:
lovenote:
t0:
txq_fill_txEof:0018
fop:
unused:
Total LEM: phy-a 0, phy-b 0
T3 0/1/0 is down.
CT3 H/W Version: 0.1.1, CT3 ROM Version: 0.95, CT3 F/W Version: 1.3.2
PA-MC-2T3+ Multi-Channel T3 Port Adapter Installation and Configuration
5-36
70DA, irdtneg F85E, irdthtt 6F8D, irdmir
7F98
event_ptr:
0000
memdpage:
000F
apptr:
8011
tx_beacon:
0000
local_freeptr:00C8
txq_ptr:
0003
rx_channel:
00B8
rx_buf0:
7C90
rx_limit_lo:
0001
return:
0000
phya_tmax:
0000
not_rcv_pkt:
0030
t1:
unused:
9070
phyb_ls_flag: 0001
0000
bogus_claim:
Hardware is 2CT3+ single wide port adapter
Chapter 5
Configuring Channelized mode for the Cisco PA-MC-2T3+
FFFF0BDC
0088
cmdreg:
0006
0000
memaptr:
0000
0004
tx_channel:
0000
F016
tx_beacon_bc:
8011
hold_ctl:
0003
00CC
tx_accptr:
0045
0000
rx_eof_channel:0000
7CB0
rx_buf1:
7CA0
0004
rx_limit_hi:
00AD
0000
phya_ls_flag:
0001
1388
unused:
0000
0000
phyb_tmin:
0000
FE60
t2:
002E
0288
cur:
7F30
lst_fint:
9070
0000
robin:
0000
argreg:
0003
afaddr:
0602
tx_claim: F002
tx_clbn:
0000
unused:
B000
raw_ptr:
0080
rx_error: 00A0
rx_next0: 7C98
rx_offset:0028
unused:
0002
txq_fill: 0018
phyb_tmax:1388
t3:
0049
cnt:
0000
rx_count: 0004
park:
0000
OL-3526-05
Advertisement
Table of Contents
