Related Manuals for Zanussi Series 51 New
Summary of Contents for Zanussi Series 51 New
- Page 1 SERVICE MANUAL TUMBLE-DRYERS TUMBLE-DRYERS SERIE P51 NEW © ELECTROLUX ZANUSSI ELETTRODOMESTICI S.p.A. VIA GIARDINI CATTANEO, 3 Publication-No. I - 33170 PORDENONE (ITALY) 599 33 15-85/6 Fax (0434) 394096 970219 EN/SERVICE/EB...
- Page 2 - 2 -...
-
Page 3: Table Of Contents
INDEX Operating principle ..........page. Constructional features . -
Page 4: Operating Principle
OPERATING PRINCIPLE 1 - Heating unit 2 - Drum 3 - Door 4 - Filter 5 - Fan 6 - Exhaust duct Cold air Warm air This appliance is of the type discharging humid air in the ambient. In brief, the fan (5) intakes cold air from the ambient and forces it through a heating unit (1). -
Page 5: Cabinet
CABINET 1 - Base 2 - Flexible hose 3 - Ring nut 4 - Cap 5 - Back panel cover 6 - Back panel 7 - Side panels 8 - Cross piece 9 - Duct 10 - Front panel 11 - Joint 12 - Filter Cabinet/Side panel/Back panel/Base Parts made of painted sheet metal fastened together by means of self-threading screws and hooked to the... - Page 6 Air tightness at the back 1 - Felt ring 2 - Drum 3 - Back panel Drum back support 4 - Antifriction washer 5 - "Benzing" ring 6 - Back panel 7 - Drum shaft 8 - Support provided with a bushing fitted on the back panel Front support and drum seal 9 - Supporting flange...
-
Page 7: Heating Unit
MAIN ELECTRICAL PARTS HEATING UNIT 1 - Filament heating element 2 - Safety thermostat 3 - Manually resettable thermostat 4 - Ceramic boards 5 - Casing Double-filament heating element provided with ceramic boards and galvanised sheet iron frame. The heating element power can be, according to the models, 1400 + 600 or 1400 + 1000 W. -
Page 8: Timer
TIMER - Electromechanical timer including two timing sections for the drying time. The first from 0 to 120 min. for drying fast fabrics. The second from 0 to 80 min. for drying delicate fabrics. When the delicate fabrics section is selected one of the heater branches is excluded. -
Page 9: Accessibility & Serviceability
ACCESSIBILITY & SERVICEABILITY FROM THE WORKTOP - Disassemble the worktop by unscrewing the two back screws and sliding it out towards the back of the machine 1 - Timer 2 - Indicator light 3 - Door microswitch TIMER Remove the knob (see figure), remove the knob flange (see figure); undo the two fastening screws. -
Page 10: Motor
FROM THE RIGHT HAND SIDE - Disassemble the worktop - Disassemble the right hand side by unscrewing the two top screws fastening it to the front panel and to the back panel and then slide it out upwards and then outwards. 4 - Motor/fan unit 5 - Capacitor 6 - Tension spring... -
Page 11: Back Panel Cover
FROM THE BACK PANEL COVER - Undo the screws fastening the back panel 9 - Heating element 10 - Back drum support HEATING ELEMENT Remove the two screws fastening it to the back panel, disconnect wiring. SSAFETY THERMOSTATS In case of failure, replace the whole heating unit. REAR DRUM SUPPORT Remove the "Benzing"... -
Page 12: Back Panel
FROM THE BACK PANEL After having removed the back panel cover, remove the worktop, undo the screws provided at the top and fastening the back panel to the cross bar and to the sides, and at the back undo the screws fastening the back panel to the base, disengage the tags provided on the base and slide out the back panel. -
Page 13: Door
ACCESS FROM THE DOOR DOOR To accede to the door undo the screws fastening the hinge FILTER To replace the filter screen, without disassembling the front panel and the duct, operate as follows: - take out the filter screen by means of pliers as shown in figure.