hit counter script
Lenovo ideacentre 610S Hardware Maintenance Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. I/O Systems
  5. ideacentre 610s
  6. Hardware maintenance manual

Lenovo ideacentre 610S Hardware Maintenance Manual

Hide thumbs Also See for ideacentre 610S:
Table of Contents

Advertisement

Quick Links

ideacentre 610S
Hardware Maintenance Manual
Machine Types: 90FC [610S-02ISH/Energy Star]

Advertisement

Table of Contents
loading

Related Manuals for Lenovo ideacentre 610S

Summary of Contents for Lenovo ideacentre 610S

  • Page 1 610S Hardware Maintenance Manual Machine Types: 90FC [610S-02ISH/Energy Star]...
  • Page 2 “Read this first: Important safety information” on page 1 . First Edition (May 2016) © Copyright Lenovo 2016. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant to a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No.

  • Page 3: Table Of Contents

    Trademarks ....Undetermined problems ... Chapter 6. Hardware locations ..17 © Copyright Lenovo 2016...
  • Page 4 610S Hardware Maintenance Manual...

  • Page 5: About This Manual

    Important: This manual is intended only for trained service technicians who are familiar with Lenovo computers. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively. Before servicing a Lenovo computer, be sure to read and understand Chapter 1 “Read this first: Important safety information” on page 1 .
  • Page 6 610S Hardware Maintenance Manual...

  • Page 7: Chapter 1. Read This First: Important Safety Information

    Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect any attached power cords, telecommunication cables, network cables, and modem cables before you open the computer covers, unless instructed otherwise in the installation and configuration procedures. © Copyright Lenovo 2016...
  • Page 8 – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) • If an electrical accident occurs: – Use caution; do not become a victim yourself. ideacentre 610S Hardware Maintenance Manual...

  • Page 9: Safety Inspection Guide

    – Switch off power. – Send another person to get medical aid. Safety inspection guide The intent of this inspection guide is to assist you in identifying potential hazards posed by these products. Each computer, as it was designed and built, had required safety items installed to protect users and service personnel from injury.

  • Page 10: Grounding Requirements

    • Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices. ideacentre 610S Hardware Maintenance Manual...
  • Page 11 To Connect To Disconnect 1. Turn everything OFF. 1. Turn everything OFF. 2. First, attach all cables to devices. 2. First, remove power cords from outlets. 3. Attach signal cables to connectors. 3. Remove signal cables from connectors. 4. Attach power cords to outlet. 4.
  • Page 12 To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices. ideacentre 610S Hardware Maintenance Manual...

  • Page 13: Chapter 2. Environment And Electrical Input

    Operating: From -15.2 m (-50 ft) to 3048 m (10 000 ft) Storage: From -15.2 m (-50 ft) to 10 668 m (35 000 ft) Electrical input Input voltage: From 100 V ac to 240 V ac Input frequency: 50/60 Hz © Copyright Lenovo 2016...
  • Page 14 610S Hardware Maintenance Manual...

  • Page 15: Chapter 3. General Checkout

    • If the computer displays a POST error, go to “POST error codes”. • If the computer hangs and no error is displayed, continue at step 7. 7. If the test stops and you cannot continue, replace the last device tested. © Copyright Lenovo 2016...
  • Page 16 610S Hardware Maintenance Manual...

  • Page 17: Chapter 4. Using The Setup Utility Program

    5. Exit the Setup Utility program. See “Exiting the Setup Utility program” on page 13. Using BIOS passwords By using the Setup Utility program, you can set passwords to prevent unauthorized access to your computer and data. © Copyright Lenovo 2016...

  • Page 18: Setup Utility Program Password Types

    5. Exit the Setup Utility program. See “Exiting the Setup Utility program” on page 13. Selecting a startup device If your computer does not start up from a device as expected, you can choose to change the startup device sequence permanently or select a temporary startup device. ideacentre 610S Hardware Maintenance Manual...

  • Page 19: Changing The Startup Device Sequence Permanently

    Changing the startup device sequence permanently To change the startup device sequence permanently, do the following: 1. Depending on the type of the storage device, do one of the following: • If the storage device is internal, go to step 2. •...
  • Page 20 610S Hardware Maintenance Manual...

  • Page 21: Chapter 5. Symptom-To-Fru Index

    Check that the following are properly installed: Reseat connectors • Power Cord • On/Off Switch connector • System Board Power Supply connectors • Microprocessor connections Check the power cord. Power Cord Check the power-on switch. Power-on Switch © Copyright Lenovo 2016...

  • Page 22: Post Error Codes

    3. Power-on the computer to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or component. If all devices and components have been removed and the problem continues, replace the system board. ideacentre 610S Hardware Maintenance Manual...

  • Page 23: Chapter 6. Hardware Locations

    Storage drive activity indicator Power indicator Power button Headset connector (also known as combo audio jack) SPDIF-out connector Power adapter connector Ethernet connector Wireless reset button HDMI -out connector USB 3.0 connectors (4) Card reader slot © Copyright Lenovo 2016...

  • Page 24: Major Frus And Crus

    Major FRUs and CRUs Note: Depending on your computer model, some of the following components might not be available. Figure 2. Major FRUs and CRUs ideacentre 610S Hardware Maintenance Manual...
  • Page 25 The following table lists the major FRUs shown in the illustration above and identifies which FRUs are also self-service CRUs or optional-service CRUs. Notes: • Self-service CRUs: These CRUs are secured by no more than two screws. Examples of these CRUs include the keyboard, the mouse, USB devices, and the power cord.

  • Page 26: Parts On The Main Boards

    “Front view and rear view” on page 17. Figure 3. Parts on the I/O board Pogo pin board connector Power connector (connected to the discrete graphics card) I/O connector (connected to the system board) HDMI connector (connected to the system board) ideacentre 610S Hardware Maintenance Manual...
  • Page 27 Parts on the system board Figure 4. Parts on the system board M.2 Wi-Fi card slot Top fan connector Card reader connector SATA connector (connected to the storage drive board) Memory slot Wireless card connector Power button board connector HDMI connector (connected to the I/O board) I/O connector (connected to the I/O board) PCI Express connector (connected to the discrete graphics card)
  • Page 28 Parts on the storage drive board Figure 5. Parts on the storage drive board M.2 solid-state drive slot SATA connector (connected to the system board) SATA connector (connected to the 2.5-inch storage drive) ideacentre 610S Hardware Maintenance Manual...

  • Page 29: Chapter 7. Installing Or Replacing Hardware

    • When installing or replacing an option, use the appropriate instructions in this section along with the instructions that come with the option. • In most areas of the world, Lenovo requires the return of the defective CRU. Information about this will come with the CRU or will come a few days after the CRU arrives.
  • Page 30 2. Unlock all locking devices that secure the computer covers. 3. If the computer is shipped with the projector, remove the top cover first as shown. Figure 6. Removing the top cover ideacentre 610S Hardware Maintenance Manual...
  • Page 31 4. Remove the bottom cover as shown. Figure 7. Removing the bottom cover 5. Remove the rear I/O cover as shown. Figure 8. Removing the rear I/O cover Chapter 7 Installing or replacing hardware...

  • Page 32: Replacing The I/O Board Shield

    1. Remove all media from the drives and turn off all connected devices and the computer. Then, disconnect all power cords from electrical outlets and all cables that are connected to the computer. 2. Remove the computer covers. See “Removing the computer covers” on page 23. ideacentre 610S Hardware Maintenance Manual...

  • Page 33: Replacing The I/O Board

    3. Remove the I/O board shield as shown. Figure 10. Removing the I/O board shield 4. Install the new I/O board shield. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 47. Replacing the I/O board Attention: Do not open your computer or attempt any repair before reading and understanding the Chapter 1 “Read this first: Important safety information”...

  • Page 34: Replacing The Discrete Graphics Card

    Attention: Do not open your computer or attempt any repair before reading and understanding the Chapter 1 “Read this first: Important safety information” on page 1 . To replace the discrete graphics card, do the following: ideacentre 610S Hardware Maintenance Manual...
  • Page 35 1. Remove all media from the drives and turn off all connected devices and the computer. Then, disconnect all power cords from electrical outlets and all cables that are connected to the computer. 2. Remove the computer covers. See “Removing the computer covers” on page 23. 3.

  • Page 36: Replacing The Power Button Board

    2. Remove the computer covers. See “Removing the computer covers” on page 23. 3. Remove the power button board. See “Replacing the power button board” on page 30. ideacentre 610S Hardware Maintenance Manual...

  • Page 37: Replacing The System Board Shield And The Storage Drive Board Shield

    4. Remove the wireless card as shown. Figure 16. Removing the wireless card 5. Connect the wireless card cable to the new wireless card. 6. Install the new wireless card. 7. Reinstall the power button board. See “Replacing the power button board” on page 30. What to do next: •...

  • Page 38: Replacing The Storage Drive

    3. Remove the I/O board shield. See “Replacing the I/O board shield” on page 26. 4. Remove the power button board. See “Replacing the power button board” on page 30. 5. Remove the wireless card. See “Replacing the wireless card” on page 30. ideacentre 610S Hardware Maintenance Manual...
  • Page 39 6. Remove the system board shield and the storage drive board shield. See “Replacing the system board shield and the storage drive board shield” on page 31. 7. Remove the 2.5-inch storage drive as shown. Figure 18. Removing the 2.5-inch storage drive 8.

  • Page 40: Replacing The Storage Drive Board

    31. 7. Record the cable routing and cable connections, and then disconnect all cables from the storage drive board. 8. Remove the storage drive. See “Replacing the storage drive” on page 32. ideacentre 610S Hardware Maintenance Manual...

  • Page 41: Replacing The Card Reader

    9. Remove the storage drive board as shown. Figure 20. Removing the storage drive board 10. Install the new storage drive board. 11. Route all the cables that you disconnected from the failing storage drive board, and then connect the cables to the new storage drive board.

  • Page 42: Replacing The Pogo Pin Board And The Top Fan

    6. Remove the system board shield and the storage drive board shield. See “Replacing the system board shield and the storage drive board shield” on page 31. 7. Remove the card reader. See “Replacing the card reader” on page 35. ideacentre 610S Hardware Maintenance Manual...
  • Page 43 8. Lift the pogo pin board as shown. Figure 22. Lifting the pogo pin board 9. Lift the top fan as shown. Figure 23. Lifting the top fan 10. Disconnect the top fan cable from the system board, and then remove the top fan from the chassis. 11.

  • Page 44: Replacing The Wi-Fi Antennas

    18. Reinstall the I/O board shield. See “Replacing the I/O board shield” on page 26. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 47. ideacentre 610S Hardware Maintenance Manual...

  • Page 45: Replacing The Wi-Fi Card

    Replacing the Wi-Fi card Attention: Do not open your computer or attempt any repair before reading and understanding the Chapter 1 “Read this first: Important safety information” on page 1 . To replace the Wi-Fi card, do the following: 1. Remove all media from the drives and turn off all connected devices and the computer. Then, disconnect all power cords from electrical outlets and all cables that are connected to the computer.

  • Page 46: Replacing The System Board

    31. 7. Remove the memory module. See “Replacing the memory module” on page 39. 8. Record the cable routing and cable connections, and then disconnect all cables from the system board. ideacentre 610S Hardware Maintenance Manual...
  • Page 47 9. Remove the system board as shown. Figure 27. Removing the system board 10. Turn over the system board, and then remove the microprocessor as shown. Notes: • Your microprocessor and socket might look different from the one illustrated. • Touch only the edges of the microprocessor. Do not touch the gold contacts on the bottom. •...

  • Page 48: Replacing The Coin-Cell Battery

    6. Remove the system board shield and the storage drive board shield. See “Replacing the system board shield and the storage drive board shield” on page 31. 7. Remove the system board. See “Replacing the system board” on page 40. ideacentre 610S Hardware Maintenance Manual...

  • Page 49: Replacing The Microprocessor

    8. Turn over the system board, and then remove the coin-cell battery as shown. Figure 29. Removing the coin-cell battery 9. Install the new coin-cell battery. 10. Reinstall the system board. 11. Reinstall the storage drive board shield and the system board shield. See “Replacing the system board shield and the storage drive board shield”...

  • Page 50: Replacing The Heat Sinks

    CAUTION: The heat sinks might be very hot. Before you open the computer covers, turn off the computer and wait several minutes until the computer is cool. To replace the heat sinks, do the following: ideacentre 610S Hardware Maintenance Manual...
  • Page 51 1. Remove all media from the drives and turn off all connected devices and the computer. Then, disconnect all power cords from electrical outlets and all cables that are connected to the computer. 2. Remove the computer covers. See “Removing the computer covers” on page 23. 3.

  • Page 52: Replacing The Bottom Fan

    2. Remove the computer covers. See “Removing the computer covers” on page 23. 3. Remove the I/O board shield. See “Replacing the I/O board shield” on page 26. 4. Remove the I/O board. See “Replacing the I/O board” on page 27. ideacentre 610S Hardware Maintenance Manual...

  • Page 53: Completing The Parts Replacement

    5. Remove the discrete graphics card. See “Replacing the discrete graphics card” on page 28. 6. Remove the power button board. See “Replacing the power button board” on page 30. 7. Remove the wireless card. See “Replacing the wireless card” on page 30. 8.
  • Page 54 9. Depending on the parts you installed or replaced, you might need to confirm the updated information. See Chapter 4 “Using the Setup Utility program” on page 11. 10. If a newly installed hardware component does not work normally, update the device driver. ideacentre 610S Hardware Maintenance Manual...

  • Page 55: Chapter 8. Fru Lists

    00XL108 Fru,Power _Led cable 00XL102 Fru,100mm CR Cable 00XL128 Fru,FPC 22 PIN PWR cable Board FRU P/N CRU ID Description 00XK042 Consumer Tiny GFX_IO B2B board 00XK036 IO Board Tiny ROW 00XK032 IO Board Tiny PRC © Copyright Lenovo 2016...
  • Page 56 Fru, LINECORD,IN,1M,3P,NON-LH 00XL082 Fru, LINECORD,ZA,1M,3P,NON-LH 00XL052 Fru, US/CA,1M,3P,NON-LH 00XL071 Fru, LINECORD,CH,1M,3P,NON-LH 00XL097 Fru, LINECORD,TH,1M,3P,NON-LH 00XL003 Fru, JP,Anti-TR,1M,2P,NON-LH 00XL075 Fru, LINECORD,GB,1M,3P,NON-LH 00XL091 Fru, LINECORD,TW,1M,3P,NON-LH 00XL094 Fru, LINECORD,IN,1M,3P,NON-LH 00XL079 Fru, LINECORD,AU,1M,3P,NON-LH 00XL090 Fru, LINECORD,CN,1M,3P,NON-LH 00XL059 Fru, LINECORD,AR,1M,3P,NON-LH ideacentre 610S Hardware Maintenance Manual...
  • Page 57 FRU P/N CRU ID Description 00XL062 Fru, LINECORD,BR,1M,3P,NON-LH 00XL073 Fru, LINECORD,IT,1M,3P,NON-LH 00XL093 Fru, LINECORD,TW,1M,3P,NON-LH 00XL081 Fru, LINECORD,ZA,1M,3P,NON-LH 00XL077 Fru, LINECORD,GB,1M,3P,NON-LH 00XL070 Fru, LINECORD,CH,1M,3P,NON-LH 00XL085 Fru, LINECORD,IL,1M,3P,NON-LH 00XL076 Fru, LINECORD,GB,1M,3P,NON-LH 00XL065 Fru, EU/KR,1M,3P,NON-LH 00XL064 Fru, EU/KR,1M,3P,NON-LH 00XL080 Fru, LINECORD,AU,1M,3P,NON-LH 00XL063 Fru, EU/KR,1M,3P,NON-LH 00XL051 Fru,US/CA,1M,3P,NON-LH 00XL084...
  • Page 58 Description 00JT086 128G,M.2,2280,SATA6G,LTON,STD 00JT008 128G,M.2,2280,SATA6G,SAMSG,STD Wireless FRU P/N CRU ID Description 00JT471 Wireless,CMB,LTN,NFA344 V2 00JT507 Wireless,CMB,IN,3165 ac Ind 00JT506 Wireless,CMB,IN,8260 NV Ind 00JT454 Wireless,CMB,LTN,8821AE 00JT480 Wireless,CMB,IN,8260 ac NV 00JT497 Wireless,CMB,IN,3165 ac 01AJ400 L2-SK63102 WirelessHD Transmi ideacentre 610S Hardware Maintenance Manual...

  • Page 59: Chapter 9. Additional Service Information

    • Wake Up on Alarm: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event , a daily event or a weekly event. • Wake Up on LAN: This feature allows LAN adapter card to wake the System. © Copyright Lenovo 2016...
  • Page 60 610S Hardware Maintenance Manual...

  • Page 61: Trademarks

    Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: ideacentre Lenovo The Lenovo logo Windows is a trademark of the Microsoft group of companies. Other company, product, or service names may be trademarks or service marks of others.
  • Page 62 610S Hardware Maintenance Manual...

Table of Contents