Safety Guidelines - Cisco 12012 Replacement Instructions Manual
Gigabit switch router dc-input
power supply
Hide thumbs
Also See for 12012:
- Replacement instructions manual (34 pages) ,
- Installation instructions manual (14 pages) ,
- Installation and configuration manual (310 pages)
Table of Contents
Advertisement
The LEDs indicate the following:
•
Input OK LED—When the power switch is turned on, this green LED should go on immediately,
indicating that the source DC voltage is within the operational range of –40.5 to –75 VDC. If the
power switch is on and the LED remains off, either the source voltage is not present or exceeds
the operational range.
•
Output fail LED—If this red LED is on, one or both of the power supply output voltages (+5 and
–48 VDC) is out of tolerance. When the power supply is first turned on, the output fail LED
blinks on and off for five seconds, then turns off. If the LED stays on, a fault has been detected
within the power supply.
Safety Guidelines
Before you begin the replacement procedure, review the safety guidelines in this section to avoid
injuring yourself or damaging the equipment. This section also repeats in multiple languages the
warnings in this document.
In addition, review the safety warnings listed in the document Regulatory Compliance and Safety
Information for the Cisco 12012 Gigabit Switch Router (Document Number 78-4347-xx) that
supports your Cisco 12012 before installing, configuring, or maintaining the router.
Safety Warnings
Following are translations for the warning statements used in this document:
Warning
Before you work on any equipment, be aware of the hazards involved with electrical circuitry and
be familiar with standard practices for preventing accidents. To see translations of the warnings that
appear in this publication, refer to the Regulatory Compliance and Safety Information document that
accompanied this device.
Waarschuwing
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust
te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van
standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die
in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information
(Informatie over naleving van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is
ingesloten.
Varoitus
Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä
vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien
varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety
Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).
Attention
pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement,
soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les
procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des
traductions d'avertissements figurant dans cette publication, consultez le document Regulatory
Compliance and Safety Information (Conformité aux règlements et consignes de sécurité) qui
accompagne cet appareil.
This warning symbol means danger. You are in a situation that could cause bodily injury.
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die
Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan.
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation
Cisco 12012 Gigabit Switch Router DC-Input Power Supply Replacement Instructions
Safety Guidelines
5
Advertisement
Table of Contents
