KV-36FS100/36FS200/38FS200 Self Diagnosis SELF-DIAGNOSTIC FUNCTION Supported model The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER LED will automatically begin to flash. The number of times the LED flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 3
KV-36FS100/36FS200/38FS200 Stopping the Standby/Timer LED Flash Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER LAMP from fl ashing. Self-Diagnostic Screen Display For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confi rmed, it is possible to bring up past occurrences of failure on the screen for confi...
Page 4
KV-36FS100/36FS200/38FS200 +B overcurrent (OCP) Occurs when an overcurrent on the +B (135V) line is detected by pin 48 of IC001 (A Board). If the voltage of pin 48 of IC001 (A Board) is less than 1V when V.SYNC is more than seven verticals in a period, the unit will automatically turn off.
KV-36FS100/36FS200/38FS200 SECTION 4: CIRCUIT ADJUSTMENTS ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER Use the Remote Commander (RM-Y180, RM-Y181) to perform the circuit adjustments in this section. Test Equipment Required: 1. Pattern generator 2. Frequency counter 3. Digital multimeter 4. Audio oscillator 4-2. MEMORY WRITE CONFIRMATION 4-1.
KV-36FS100/36FS200/38FS200 4-4. SERVICE DATA LISTS Non-Volatile Memory (NVM) Reference for BA5D Service List Common Service No. Name Description Slave Init Group Addr Addr Data VERSION Microprocessor version information Common NTSC / PAL-M PAL-N Service Fix / Name Description Slave Slave Sub...
Page 7
KV-36FS100/36FS200/38FS200 SERVICE DATA LISTS Common NTSC PAL-M PAL-N Service Fix / Name Description Slave Slave Sub Slave Slave Group Addr Addr Data Data Addr Addr Data Addr Addr Data Addr Addr Data REFP REFP JPSW Jump SW SHUE Sub HUE adjustment...
Page 8
KV-36FS100/36FS200/38FS200 SERVICE DATA LISTS Common Service Fix / No. Name Description Slave Group Addr Addr Data COL_TMP GDOF G DRIVE Offset BDOF B DRIVE Offset GCOF G CUT Offset BCOF B CUT Offset DCOL Dinamic Color Common Service Fix / No.
Page 9
KV-36FS100/36FS200/38FS200 SERVICE DATA LISTS Common Service Fix / No. Name Description Slave Group Addr Addr Data 3L_COMB FUNN Function (0 / 7-6) for NTSC FUNP Function (0 / 7-6) for PAL-N, PAL-M DRNG DRANG (0 / 2) YCSM Y/C Sep Mode (0 / 1-0)
Page 10
KV-36FS100/36FS200/38FS200 SERVICE DATA LISTS Common Service Fix / No. Name Description Slave Group Addr Addr Data 3D_COMB 31 YPFT YPFT(0B / 4-5) 32 YPFG YPFG(0B / 0-3) V1PS V1PS(0C / 6-7) 34 VEGS VEGS(0C / 4-5) 35 CC3N CC3N(0C / 3)
Page 11
KV-36FS100/36FS200/38FS200 SERVICE DATA LISTS Common Service Fix / No. Name Description Slave Group Addr Addr Data PFRN VCXO oscilation HD/VD input synchronous mode PRVS selection PCON PIP sub contrast control PUCO PIP U level control PVCO PIP V level control...
KV-36FS100/36FS200/38FS200 SERVICE DATA LISTS Service Fix / Name Description Slave Init Group Addr Addr Data Data SBAL Sub Balance SBAS Sub Bass STRE Sub Treble Surround level BBOH Surround Off - BBE high BBOL Surround Off - BBE low BBSH...
KV-36FS100/36FS200/38FS200 4-6. A BOARD ADJUSTMENTS 4-6-4. DISPLAY POSITION ADJUSTMENT (DISP) 4-6-1. H. FREQUENCY (FREE RUN) CHECK 1. Input a color-bar signal. 1. Input a TV mode (RF) with no signal. 2. Set to Service Adjustment Mode. 2. Connect a frequency counter to base of Q501 3.
Page 14
KV-36FS100/36FS200/38FS200 4-6-6. SUB HUE, SUB COLOR ADJUSTMENT 4-6-9. H. CENTER ADJUSTMENT (HPOS) (SHUE, SCOL) Perform this adjustment after performing H. Frequency (Free Run) Check. 1. Input color-bar signal at 75%. 1. Input a crosshatch signal. 2. Activate the Service Adjustment Mode.
Page 15
KV-36FS100/36FS200/38FS200 4-6-12. V. ANGLE (VANG), V. BOW (VBOW), UPPER PIN (UPIN) AND LOW PIN (LPIN) ADJUSTMENTS 1. Input a crosshatch signal. 2. Activate the Service Adjustment Mode. 3. Select VANG, VBOW, UPIN, and LPIN with 1 and 4 . 4. Adjust with 3 and 6 for the best picture.
BA-5D SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION CHASSIS NO. KV-36FS100 RM-Y180 SCC-S65H-A KV-36FS100 RM-Y180 SCC-S64F-A KV-36FS100 RM-Y180 HAWAII SCC-S67B-A KV-36FS200 RM-Y181 SCC-S65J-A KV-36FS200 RM-Y181 HAWAII SCC-S67V-A KV-38FS200 RM-Y181 LATIN NORTH SCC-S62M-A CORRECTION - 1 SUBJECT: REPLACED GK BOARD IC VOLTAGE LIST (IC600) REPLACED GK BOARD TRANSISTOR VOLTAGE LIST (Q600, Q601) Correct the service manual as shown.