Related Manuals for Toro 30834
Summary of Contents for Toro 30834
- Page 1 Form No. 3393-163 Rev A 27in Rotary Cutting Unit Groundsmaster ® 3500-D/3505-D/4500-D/4700-D Model No. 30834—Serial No. 315000001 and Up *3393-163* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
(Groundsmaster 3500-D and 3500-G only) ..............9 You may contact Toro directly at www.Toro.com for product Greasing the Bearings ..........9 and accessory information, help finding a dealer, or to register Separating the Cutting Decks from the Traction your product. -
Page 3: Safety
Safety This machine has been designed in accordance with EN ISO 5395:2013 and ANSI B71.4-2012. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 104-1086 1. -
Page 4: Setup
Setup Media and Additional Parts Description Qty. CE Decal Apply to the cutting deck for CE compliance. Operator's Manual Read before operating. Parts Catalog Use to lookup parts. Adjusting the Carrier Frame Note: This increases the chamber to carrier clearance due to the higher position of the cutting chamber, but (Groundsmaster 3500-D and will cause the cutting deck to reach their maximum up... -
Page 5: Adjusting The Roller Scraper (Optional)
G011346 Figure 5 1. Roller spacer 3. Grease fitting 2. Mounting screw 2. Slide the scraper up or down until a gap of 0.020 to Figure 3 0.040 inch (0.5 to 1 mm) is achieved between the rod and the roller. 1. -
Page 6: Product Overview
Contact your Authorized Service Dealer or • Discharge has less tendency to throw left and thus a Distributor or go to www.Toro.com for a list of all approved cleaner look around bunkers and fairways. attachments and accessories. •... -
Page 7: Operating Tips
Atomic Blade This blade was designed to provide excellent leaf mulching. Attributes: Excellent leaf mulching Operating Tips Mow when the Grass is Dry Mow either in the late morning to avoid the dew, which causes grass clumping, or in late afternoon to avoid the damage that can be caused by direct sunlight on the sensitive, freshly mowed grass. - Page 8 Choosing Accessories Optional Equipment Configuration Angle Sail Blade High Lift Parallel Mulching Baffle Roller Scraper Sail Blade Do not use with the mulching baffle Grass Cutting: 0.75 to Recommended in most May work well in light or Has been shown to Can be used any time 1.75 inch (1.9 to 4.4 cm) applications...
-
Page 9: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check the blade stopping time. Before each use or daily • Grease the bearings Every 50 hours CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. -
Page 10: Separating The Cutting Decks From The Traction Unit
G011349 Figure 9 Important: Make sure the grease groove in each roller mount aligns with the grease hole in each end of the roller shaft. To help align the groove and hole, there is Figure 11 also an alignment mark on one end of the roller shaft. 1. -
Page 11: Removing The Cutter Blade
Always use genuine If any of these measurements are not within specification, Toro replacement blades to be sure of safety and optimum proceed to Adjusting the Blade Plane. performance. Never use replacement blades made by other manufacturers because they could be dangerous. -
Page 12: Inspecting And Sharpening The Blade
If this time is greater than 7 seconds, the braking valve needs adjustment. Call your Toro Distributor for assistance in making this adjustment. -
Page 13: Storage
Storage 2. Insert a punch through the end of the roller housing and drive the opposite bearing out by alternating taps to the opposite side of inner bearing race. There should If the cutting deck is separated from the traction unit for any be a 0.060 inch (1.5 mm) lip of inner race exposed. - Page 14 Notes:...
- Page 15 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.