Proline 53cm recycler ii walk power lawn mower (28 pages)
Summary of Contents for Toro Recycler 22170
Page 1
Pour obtenir gratuitement une version en français de ce manuel, écrivez à l’adresse ci–dessous. N’oubliez pas d’indiquer les numéros de modèle et de série de votre produit. The Toro Company, Attn: Parts Dept., 8111 Lyndale Ave S, Bloomington, MN 55420–1196. Domestic English (EN)
Safe Operating Practices The Toro warning system in this manual identifies potential hazards and has special safety messages that help you and others avoid personal injury, even death. This product is capable of amputating hands and feet and DANGER, WARNING and CAUTION are signal words throwing objects.
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. Model 22170 only ON MOWER HOUSING ON MOWER HOUSING ON MOWER HOUSING (Part No.
m–210 Figure 2 m–275 1. Rope guide 2. Starter rope Figure 4 1. Spring clip Install Discharge Tunnel Plug 1. Open the discharge door by pulling forward on the Before Starting handle and moving it rearwards (Fig. 3). Hold the discharge door handle to prevent the spring–loaded door from closing while inserting the plug.
Do not fill the fuel tank completely full. Add Toro also recommends that Toro Stabilizer/Conditioner be gasoline to the fuel tank until the level is 1/4” to used regularly during operation and storage. Toro 1/2”...
Toro Stabilizer/Conditioner. Toro Stabilizer/Conditioner is a petroleum distillate based Ground speed control is located at rear of belt cover product. Toro does not recommend stabilizers with an (Fig. 9). alcohol base such as ethanol, methanol, or isopropyl. Do not use additives to enhance the power or performance of the engine.
3. To engage the self-propel drive, squeeze the control bar against the handle to the RUN/DRIVE position (Fig. 10). m–1914 m-3769 Figure 11 Figure 10 1. Discharge door handle 2. Plug tilted clockwise 1. RUN/DRIVE position 3. STOP position 2. RUN/SHIFT position 4.
Page 10
WHAT CAN HAPPEN Thrown objects can cause serious personal injury or death to operator or bystanders. HOW TO AVOID THE HAZARD Check the grass bag frequently. If it is damaged, install a new genuine TORO replacement bag. m–1912 DANGER Figure 13 1.
Periodically file down nicks on blade. Replace the blade when necessary with an original POTENTIAL HAZARD Toro replacement blade. Adjusting the height-of-cut levers could bring your hands into contact with the moving blade. Only mow dry grass or leaves. Wet grass and leaves...
Check stopping time every 50 hours or at the start of each mowing season. Blade must Blade Brake stop within 3 seconds of releasing bail; if not, see your Authorized Toro Service Dealer for repair. Grease rear height adjustor Lubrication brackets (self-propelled models).
After every Service Item Service Operation Hours Hours Hours Hours Hours Remove and clean grass, Belt Cover clippings and debris from under cover. Change engine oil after first 8 hours of operation. Thereafter, Engine Oil change engine oil every 50 hours (without oil filter) and every 100 hours (with oil filter).
4. Open the fuel valve by turning the lever to the open position (Fig. 7). 5. Drain gasoline completely from the tank and fuel line into an approved gasoline container. 6. Remove the fuel tube on the fuel tank by loosening the tube clamp (Fig.
6. Raise right side of mower until all oil has flowed into 3. Drain the engine oil as specified in Engine Oil section, the drain pan. page 14. 7. Remove the oil drain tube and retighten the side oil 4. Place a suitable drain pan under the oil filter drain plug.
3. Set the gap on the new plug to 0.030” (0.76 mm) (Fig. 21). .030 in. (.76 mm) Figure 23 1. One inch Figure 21 4. Install the spark plug and gasket seal. Tighten the plug Adjusting the Blade Brake to 17 ft-lb (23 N m).
Hand Push Model (Fig. 25) WARNING Loosen jam nut on brake cable. Insert / ”- / ” object between brake lever and handle. Turn cable POTENTIAL HAZARD adjuster on brake cable until slack is removed. Then Gasoline is extremely flammable, highly tighten nut.
A. If a slot or wear is noticed, (Fig. 27B & C), replace the blade. Refer to the Removing and Installing the Blade sections. B. If the blade is nicked or dull, sharpen it. Refer to Figure 29 the Removing, Sharpening, Balancing, and Installing the Blade sections.
Lubricating the Self–propel Cleaning the Underside of the Drive Mower Housing 1. Wipe the grease fittings on the rear height-of-cut To ensure best performance, keep the underside of the adjustors (Fig. 31) with a clean rag. mower housing clean. Be especially careful to keep the kickers free of debris (Fig.
Scraping Method If washing does not remove all debris from under the mower, tip it and scrape it clean. 1. Pull the wire off of the spark plug (Fig. 6). 2. Drain the gasoline from the fuel tank. Refer to the Draining Gasoline and Cleaning Fuel Filter section, page 14.
Mount screws or bolts in opposing holes. Troubleshooting Your mower was designed and built for trouble-free operation. Check the following components and items carefully. If a problem continues, see your Authorized Toro Service Dealer. PROBLEM CORRECTIVE ACTION Engine will not start 1.
Maintaining the Blade section, page 17. enclosure. 2. Tighten all nuts, bolts, and screws. We recommend Toro Fuel Conditioner to stabilize fuel for 3. Lubricate the wheels. Refer to the Lubricating the storage. If possible, the last fuel fill of the year should be Self–Propel Drive section, page 19.
8. Connect the spark plug wire (Fig. 6). Accessories Accessories may have been shipped with your mower or are available from your Authorized Toro Dealer. Side Discharge Kit, Model No. 59199—Install in seconds. Rear mounted in place of the grass bag.