Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Related Manuals for Panasonic A14
Summary of Contents for Panasonic A14
- Page 1 Camera A14 and A34 Dome Camera Quick Start Guide...
- Page 2 About This Manual: This manual applies to A14 and A34 dome camera. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual.
-
Page 3: Regulatory Information
Network Dome Camera Quick Operation Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 4 Network Dome Camera Quick Operation Guide equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information.
-
Page 5: Safety Instruction
Network Dome Camera Quick Operation Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. - Page 6 Network Dome Camera Quick Operation Guide Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
- Page 7 Network Dome Camera Quick Operation Guide To avoid heat accumulation, good ventilation is required for operating environment. Keep the camera away from liquid while in use. While in delivery, the camera shall be packed in its original packing, or packing of the same texture.
- Page 8 Network Dome Camera Quick Operation Guide Table of Contents 1 Overview ......................8 2 Installation ...................... 10 3 Setting the Network Camera over the LAN ............. 14 4 Accessing via Web Browser ........Error! Bookmark not defined.
-
Page 9: Overview
Network Dome Camera Quick Operation Guide Overview Figure 1-1 Overview... - Page 10 Network Dome Camera Quick Operation Guide Table 1-1 Physical Description Description Mounting Base Horizontal Stand Vertical Stand Bubble Cables IR Led Lens Black Liner Safety Cable...
-
Page 11: Installation
Network Dome Camera Quick Operation Guide Installation Before you start: Please make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. ... - Page 12 Network Dome Camera Quick Operation Guide Loosen the set screws with a hex key (supplied) to remove the bubble. Figure 2-2 Remove the Bubble Connect the corresponding cables. If required, you can route cables through the side opening on the side of the mounting base.
- Page 13 Network Dome Camera Quick Operation Guide Fix the mounting base to the ceiling with screws. Figure 2-4 Fix the Mounting Base Adjust the surveillance angel. Loosen the tilt adjusting screws, and adjust the tilt angel [0~65], and tighten the tilt adjusting screws. Hold the black liner and rotate it to adjust the pan position [0~360].
- Page 14 Network Dome Camera Quick Operation Guide As the lens has already been factory adjusted to the best imaging effect, you just need to adjust the pan position and tilt position to get the desired surveillance angle. Reinstall the bubble and tighten the screws. Figure 2-6 Complete the Installation...
-
Page 15: Setting The Network Camera Over The Lan
Network Dome Camera Quick Operation Guide Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then install the iVMS-4200 software to search and change the IP address of the network camera. - Page 16 Network Dome Camera Quick Operation Guide download the Camera Finder manual from the Advidia Website www.advidia.com/support): After launching the Advidia Camera Finder software, it automatically searches the online devices from the subnet where your computer is located. This search may take 30 seconds or more depending on network size. After searching it will show total number and information of the Advidia cameras found on the network.
-
Page 17: Modify Device Information
Network Dome Camera Quick Operation Guide You can click on each column heading to order the information. Modify device information Steps: 1). Select the device(s) to be modified in the device list as shown in Figure 3-3. 2). Click on “File” and select “Login Manager” as shown in Figure 3-4 to enter the username and password information of selected device(s). - Page 18 Network Dome Camera Quick Operation Guide Figure 3-4 Login Manager Figure 3-5 Launch Edit Table Figure 3-6 Edit Table Enter the desired IP address (or range if changing the IP address of more than one device) of the network camera in the address field of the edit table...
- Page 19 Network Dome Camera Quick Operation Guide and click Apply Network Changes. You can also select “Dynamic IP” if you would prefer to have an IP address assigned by your network router. The default value of the IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”.
-
Page 20: Accessing Via Web Browser
Network Dome Camera Quick Operation Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and... - Page 21 Network Dome Camera Quick Operation Guide Figure 4-1 Login Interface Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
- Page 22 Network Dome Camera Quick Operation Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in...
- Page 23 Network Dome Camera Quick Operation Guide Figure 4-4 Install Plug-in Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login. Note: For detailed instructions of further configuration, please refer to the camera’s user manual...