Related Manuals for Sony ASH56NVIR
Summary of Contents for Sony ASH56NVIR
- Page 1 Operation Manual of Outdoor High-Speed Pan/Tilt with Infrared Lighting VER:2.20 Pleased read the manual carefully before using the product.
-
Page 2: Notes For Attention
I. Notes for Attention Read the manual carefully before installing the product. There are two input ways of power supply: DC12V (vehicle) and AC24V (normal pan/tilt). Detailed connections refer to the description files. There are sophisticated optical and electronic components inside the product. Avoid incorrect operation methods such as heavy pressing or strong vibration during the course of transportation, store and installation otherwise the product could be damaged. - Page 3 seconds and data are kept in memory even power is failure. e. Character superimposing function. It can display the address of the pan/tilt, title of the preset position etc. Long focus speed-limited function. The pan/tilt can adjust automatically the manual control speed depending on the focal length of the camera.
-
Page 4: Display Setup
6. Infrared System a. The infrared system is normally under automatic control state. The infrared lamp shall act followed by open/close of the low illumination of the camera; b. The open/close state of the infrared lamp can be changed by the menu manually; c. -
Page 5: Camera Setup
2.2.3 TITLE DIS： when it is set at ON, the title of the preset position can be displayed on the left side of the screen when calling the preset position, such as “NO.001 ABCDEFGH”. If no title of the position, then only “NO. - Page 6 into the manual control; if changing back into the automatic control, the user should set the option on the menu of the infrared at OFF. 2.4.4 WIPER：WIPER open/close. ( Set Preset 51 to turn ON / Call Preset 51 to turn OFF) 2.4.5 WIPER MODE：continuous or moment mode to be selected.
- Page 7 screen are as follows: The prompt messages are displayed on both op and bottom lines and information of every pattern is displayed in the middle of the screen. One line includes data of two patrol positions. Move the cursor by PAN LEFT/RIGHT and change values by TILT UP/DOWN.
- Page 8 Ω terminal resistor is opened and no bus 485 is connected; when it is at 1—2 state, 120 Ω terminal resistor is connected in parallel with the bus 485. In the bus RS485 system, there is only one pan/tilt, which has the terminal resistor to be connected in the circuit and other pan/tilts whose terminal resistors are opened so as to increase the reliability of the system.
- Page 9 Dome States of Dip-Switch Address DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6 DIP-7 DIP-8 DIP-9 DIP-10 … … 1023 SW1 is used to set the addresses of the pan/tilt which has the range from 1 to 1023. From DIP-10 to DIP-1 it corresponds to a binary number with 10 bits in which the highest bit is DIP-10 and the lowest bit is DIP-1.
- Page 10 SW2 is used to set the communication protocol and the baud rate used by the pan/tilt. Bits from DIP-4 to DIP-1 of the SW2 are used to select the protocol and 16 different protocols can be selected in maximum. The encoded table of the protocol selected by the pan/tilt is as follows: Selection of Communication Normal Baud...
- Page 11 A．7-Core Input Terminal B．10-Core Input Terminal 8.1 Description of 7-Core Terminal： 1．DC12V(AC24V): red 2．GND(AC24V): black 5．R+ (communication+): orange 3．R- (communication-): yellow 4．Null 6．V+: (VF+) 7．V-: (VF-) 8.2 Description of 10-Core Terminal： 1．Alarm-1 in: red 2．Alarm-2 in: orange 3．Alarm-3 In: yellow 4．Alarm-4 In: green 5．NC 6．Alarm In COM: black...
- Page 12 A. Installation Style of Plain Base Drawing of Sizes of the Side Drawing of Sizes of the Bottom B．Vehicle -Carried Sizes of the Shock Absorber 5.3 Installation Procedures of the Product 1. Remove the bottom plate of the pan/tilt; 2. Set the corresponding information in accordance with the schematic drawing of the dip-switch of addresses, protocols and baud rates;...
- Page 13 3. Install the bottom plate of the pan/tilt and take care of the tightness of waterproof seal ring; 4. If vehicle-carried pan/tilt is used, first of all fix the chock absorber on the bottom of the pan/tilt then fix the whole pan/tilt; 5.
- Page 14 VI. Connection Drawing of the System for Reference 6.1 Schematic Drawing of Common Pan/tilt： m oni t or Vi deo i n SELECTED ON-LINE R S485 BU S di gi t i al vi deo H D R ecor d Vi deo i n C ont r ol keyboar d R S485 BU S...
-
Page 15: Main Technical Index
VII. Main Technical Index DC12V ≥3.5A Power Supply (Option) AC24V±10% ≥2.5A Power Consumption 30VA Weight 10Kg Specifications Installation Style Plain Base Installation/Vehicle-Carried Relative Humidity 10-90% Operation Temperature -35℃~55℃ Waterproof Class IP66 Model Image Inductor 1/4″color Effective Pixels 752H×582V 795H×596V Synchronization System Inside Video Output Compound Signal1.0Vp-p/75Ω... - Page 16 VIII. Normal Troubles and Remedies Troubles Possible Causes Remedies Power supply damaged of Replace insufficient electric No action and images after power switching on Wrong connection of Make correction power supply wires Engineering circuits Remove failed Mechanic trouble Repair Abnormal self-inspection, Pan/tilt may be Re-fix images with humming of...